IO-Power USMC-12V0206-II Series
Automobile Large Consumption Fast-charging Model
Online Uninterruptible Operation + Buck Boost Voltage Convertor Power System
IOP-USMC-12V0206-II series is specifically designed for large power equipment
vehicle load system, through vehicle cigarette lighter-powered uninterruptible
operation of the system, such as on-board infrared camera, car video host, DVR/NVR
12 hour record, the range of temporary large discharge current device must be
over 12 hours or longer-lasting forms online without interrupting the operation
of the power system.
IOP-USMC-12V0206-II products, using industrial-grade automatic lifting of buck
boost voltage converter and industrial-grade protective metal casing and
mechanical design of waterproof dustproof IP66. Importing the latest technology
as high and low temperature resistant C-LiFePO4 lithium batteries, unique
security management control of charge and discharge protection, low voltage and
low power consumption ...number of proprietary technologies, achieving long-term
safety of vehicle special high power loads and equipment new applications
without interrupting the operation of power systems.
IO-Power USMC-12V0206-II series, take online type does not interrupted of
long-term power supply system design, special for strict requirements operation
in the system of not interrupted using. Its long-term of power time can over 12
hours above, for examples Cash transport van 12 hours surveillance system, bus
lane records device, police car surveillance system, preservation patrol car, 12
hours lane records device camera system, emergency rescue system and mobile
power supply system and so on, are very suitable for use.
IO-Power USMC-12V0206-II series online type Uninterruptible Operation power
system of the system components including:
1.
Input DC power
port: car cigarette lighter DC 12-28V DC power input, automatic lift voltage
converter from 18-20V / 4A (5A Max) DC voltage and current, DC UPS power system
charge and discharge operation power source.
2. Microprocessor modules: microprocessor for detecting input power management,
battery management, battery management power control, output voltage management,
system operations control detection and protection management, perform the
dimensional transport co-ordination and control of the overall system
management.
3. Charging and discharge control module: for battery voltage detection and
charging management and the battery discharge management control functions,
special design battery full charge and then enable directly power supply to load
end features, it will reduced battery of using times and improve battery using
life cycle. Auxiliary to low voltage protection and low voltage low power
discharge proprietary protection mechanism, on battery of low voltage protection
and the system fast recovery operation, provides best protection and efficient
of operation mechanism.
4. The DC power output port: DC power supply and discharge detection through
microprocessor control and protection, for loading device power requirement,
corresponds to taking the appropriate current power supply, minimum 0.5A to
maximum 6A DC current supply control.
5. The special enhanced protection measures: four seasons environment for high
and low temperature change, efficiency and battery life, may have a serious
impact, even used on the security issue. Therefore, for USMC-12V0206-II series
of vehicle-specific products, specially designed industrial grade sealed metal
shell and flame resistant high temperature resistance waterproof fittings to
avoid security problems in the use of the indoor and outdoor environment.
6. Resistance high and low temperature long-term C-LiFePO4 lithium batteries:
the vehicle through sunshine will upgrade high temperature environment, it will
operation in the system of not interrupted and more long-term using needs. The
IOP-USMC-12V0206-II series used customize of resistance high low temperature -20°C
~ +60°C long-term C-LiFePO4 lithium batteries, match
metal protection shell and institutions design, it can bear car within low
temperature -30°C ~ +75°C of
environment temperature operation. And resistance high low temperature long-term
C-LiFePO4 lithium batteries of high charging and discharging times and battery
life, it can provides less power than the traditional systems more than twice
times more electricity power capacity and 7 times more than double the service
life cycle, full vehicle large-power-line machine without interrupting the
operation of electric power systems of outstanding characteristics.
Special Description 1: Automobile internal by too Sun penetrating sunshine and
car is confined does not ventilation environment, so will produced sunshine
warming effect, in outdoor temperature up to 36°C,
car within temperature by long time sunshine warming, car within will up to
60~65°C, Sunshine direct location will up to 65~70°C
around, but as long as Sun sunshine no irradiation to of location, temperature
will slightly below car within temperature about up 55~63°C
around.
Special description 2: IO-Power USMC-12V0206-II series online type does not
interrupted operation power system, due to should car within environment of
special high temperature requirements, used resistance high temperature roast
paint package covered metal shell, in outdoor temperature up to 36°C,
car within temperature by long time sunshine warming, car within will up to
60~65°C, in Sunshine direct products shell surface
situation, shell surface temperature about 65°C, shell
within temperature about 55~58°C, C-LiFePO4 Lithium
Batteries temperature about 50~55°C ;
IOP-USMC-12V0206-II products, AM 10:00~ PM 4:00 under sunshine temperature test
for a long time in the morning, all features of normal operation and provide
stable DC 11.5V~14.4V+-3% power to the cameras inside and outside the normal
operation of the car.
IOP-USMC-12V0206-II Series Specification
|
Model |
USMC-1202-01A |
USMC-1204-02A |
USMC-1206-03A |
|
Automobile High Temperature Model
DC Jack
Iron Airtight Housing
IP 67 |
 |
|
Built In C-LiFePO4 Lithium Batteries Power Capacity |
29WH
(2.3Ah@12.8V) |
55WH
(4.3Ah@12.8V) |
74WH
(5.8Ah@12.8V) |
|
General UPS Label Size (DC Power Factor is Equal to
1) |
174VA |
330VA |
444VA |
|
Max Output Wattage (Battery Life Protection Design) |
75W/H |
75W/H |
75W/H |
|
UPS Discharge Power Supply Time |
More than 0.3hr
@75W/H Discharge |
More than 0.7hr
@75W/H Discharge |
More than 0.9hr
@75W/H Discharge |
|
Quickly Full Charge DC UPS Battery Time |
About 1hr
@3.5A Charging |
About 1.5hr
@3.5A Charging |
About 2hr
@3.5A Charging |
|
Vehicle DC Buck Boost Voltage Convertor
DC UPS system
Output DC voltage / current |
Through the car cigarette lighter or vehicle power
circuit, input DC 12~28V voltage/current 6A (8A Max), the automatic
Buck Boost Voltage Convertor (BBVC) output 20VDC/4A (5A Max) to
charge the DC UPS power supply system
Output DC voltage / current: 12VDC/6A |
|
External load voltage |
DC 11.7V~14.2V +-3% |
|
External load current |
3.5A (6A around 75W/H Max) |
|
Battery charging voltage |
13.8V~14.2V +-3% Max |
|
Battery standard charging current |
3A |
|
Transform Efficiency |
95% |
|
Strengthen the protection measures
With
Special operations functions |
l
Power outages without disrupting the operation of the
on-line operation system (monitor system not black screen)
l
MCU microprocessor starts, automatic charging and
discharging systems functioning State protection
l
Automatically detect abnormal voltage the battery
status and abnormal aging or faulty battery or battery charging
protection
l
Shell opening record of vandal detection and RS-485
signal alarm mechanism (optional function)
l
With temperature detection records with read function
mechanism
l
Mechanism of low temperature (@ -35°C)
& high temperature (@ +75°C)
protection (Please see note 3 & note 4)
l
Specially designed battery cycle life defining and
recording and control mechanisms (optional function)
l
RS-485 input / output interface, can enhance remote
management and control in real time (optional function)
l
System operation State record function
l
Support industrial MODBUS communication protocol
(allowing the PLC programmable logic control)
l
Input overvoltage protection
l
Input power supply over-current protection
l
Input of positive and negative polarity reverse
protection
l
Input short-circuit protection
l
Input lightning or power surge protection up to 1300W
l
Battery full charge, input power supply power
directly to the load, maximum output power is reached, at the same
time avoiding battery overcharge protection
l
Battery intelligent charging system protection and
the float charge function
l
Output power limit voltage protection
l
Output power limit current protection
l
Output of positive and negative polarity reverse
protection
l
Output short circuit protection
l
Output lightning or power surge protection up to
1300W
l
Battery voltage is less than 12.8V, MCU
microprocessor automatically starts into the battery low discharge
warning state
l
Battery discharge below the 11.7V,MCU microprocessor
automatically stop discharging into the battery low voltage
protection status
l
Battery voltage is lower than 11.2V, MCU
microprocessor goes into sleep protection status
l
Battery low voltage static ultra-low power protection
l
When the input power, MCU microprocessor
automatically starts recovery operation mechanism
l
After discharge low voltage battery protection to
restart the battery, special designed discharge voltage protection
function
l
Discharging under load, batteries have added support
mode power supply operation
l
Match the automatic Buck Boost Voltage Convertor (BBVC),
with car cigarette lighter power connection charging port and
protection (including fuse)
l
Match the automatic Buck Boost Voltage Convertor (BBVC),
with buck boost voltage, fixed voltage, and stabilizing the voltage
to upgrade effect of power supply protection.
l
Match the automatic Buck Boost Voltage Convertor (BBVC),
overvoltage and overcurrent and lightning / power surge protection
(30V 1500W)
l
Match the automatic Buck Boost Voltage Convertor (BBVC),
DC 18-20VDC power supply can be used as a vehicle and charge the
notebook or device for temporary
l
Specially designed "Automatically Detect the Healing
Recovery Function", to solve user errors using an action or
temporary power Input charge / output discharge for abnormal,
causing alarm fault automatic removal mechanism of State |
|
Support Battery Type |
C-LiFePO4 Lithium Batteries
Lead-acid batteries or lithium batteries or other
battery, can be customized to modify (optional function) |
|
Battery Safety Protection |
Use pressure type explosion-proof battery design |
|
Built-in battery capacity range |
1.2Ah @ 12.8V (14WH) ~ 8.7Ah @ 12.8V (111WH) |
|
Battery Charge Mode |
CC/CV MCU Automatic charging mode control |
|
Battery Charge Voltage |
14.2V +- 3% |
|
Battery Charge Float Voltage |
13.8V +- 3% |
|
Battery Cut-off Discharge Voltage |
11.7V +- 3% |
|
Battery recovery discharge voltage |
12.8V +- 3% |
|
Max. Charge Current |
4A |
|
Max. Discharge Current |
6A (Using load-discharge C-LiFePO4 Lithium Batteries,
the maximum discharge current is 6A around 75W/H) |
|
Charging and Discharging at same time, the Max.
discharge current |
3A |
|
Charging and Discharging at same time, the Max.
discharge watts |
40W/H, recommends assessing the normal functioning of
the system total power consumption, lower wattage requirements is
appropriate. |
|
Life cycle the battery 0.2C charge & 0.5C
discharge(Battery capacity remaining after using 80%, the defined
service life will terminate) |
@ 25°C
2000 Times (@ 25°C discharging 800 times:
after more than 93% capacity, @ 25°C
discharging 1100 times: after more than 90% capacity)
@ 45°C
1600 Times
@ 50°C
1200 Times
@ 60°C
550 Times
@ 60°C
720 Times 70% |
|
Industrial Housing & Connector |
Iron Airtight Housing
IP 68 Gland Connector |
|
Connector Type |
Vehicle charging circuit or car cigarette lighter,
enter 12~28V DC voltage / current 6A (8A Max)
DC output: 12V DC Jack to DC Jack connector
Input / Output I/O interface: RS-485 (optional function) |
|
Operating Temperature
(Discharge Temperature) |
-35°C
~ +75°C (Including
the chassis of the machine working temperature tolerance)
-20°C
~ +60°C (Excluding
institutions, the battery operating temperature tolerance)
+20°C
~ +40°C Battery
Capacity:100%
-10°C
Battery Capacity : 60%
-20°C
Battery Capacity : 48% |
|
Charging Temperature |
-35°C
~ +75°C (Including
the casing machine operation) |
|
Storage Temperature |
-35°C
~ +75°C，Recommendations
at +20°C ~ +30°C
environmental temperature for storage. |
|
Rel. Humidity |
10~95%RH |
|
Storage Time |
Do not wake the system can store 12 months
(after you wake the system, each 3 months charging 1 times; Please
fully charging battery in first times to use) |
|
Dimension |
DC UPS : 125mm(L)x110mm(W)x150mm(H) ; BBVC :
195mm(L)x92mm(W)x48mm(H) |
|
Weight |
1.2Kg + 0.5Kg(BBVC) |
1.4Kg + 0.5Kg(BBVC) |
1.6Kg + 0.5Kg(BBVC) |
|
LED Indicator |
1. AC input (Converted to DC power supplies): red
light constant light, show on battery in full charge status.
2. AC input (Converted to DC power supplies): red light flashing
display, represents the battery is charging status.
3. When the battery is not charging, insert the 12VDC device load
discharge, discharge the green light constant light show, shine on
behalf of low voltage in discharge, please do the charging operation
4. Simultaneous charging of the battery, insert the 12VDC device
load discharge, discharge the green light constant light show
5. AC input (Converted to DC power supplies): quick shine a red
light shows that represents an input power supply or the input port
or the battery charge State, please remove the input power terminal
as soon as possible.
6. Insert the load discharge 12VDC devices: fast shiny green display
on behalf of power output or output port or abnormal battery
discharge condition is request to remove output power connector as
soon as possible.
Note 1: when the system alarm status, please remove
the cause as soon as possible the reason for the exception. When
after eliminating abnormal, just re-switch input power supply or
plug power to supply again, the red LED flashing light signal will
resume once per second in charging status. Those processing will
remove most of the alarm status, allow the system to resume normal
operation.
Note 2: when a temporary abnormal use or abnormal
operation occurs, causing the system to start the alarm status,
specially designed automatic recovery mechanism 3 times the purpose
and again after every 10 seconds to detect anomalies and try to
exclude temporary malfunction alarm state. |
|
Housing |
IP66 |
|
Approvals |
CE & FCC |
|
Installation |
1.Street lamp pole mount
2.Upright pole mount
3.Wall mount installation
4.DIN Rail (Optional) |
|
Warranty |
Intelligent charge & discharge main board & IP66
housing & parts support two years limited warranty.
Customize C-LiFePO4 lithium batteries support one year limited
warranty. |
Note
1: Battery Capacity is +- 5%.
Note
2: Product specifications change, without notice, consultation with agent or
dealer before buying the latest specifications.
Note 3: detect the temperature reached -30℃,
start the red LED have low temperature warning, reach low temperature -35
℃, a start-stop system function will enable, when
temperatures returned to above -30℃, normal operation
will resume.
Note 4: detect the temperature reached +70℃,
start red LED have high temperature warning, reach high temperature +75℃,
a start-stop system function will enable, when temperatures back below +70℃
temperature, normal operation will resume.
